111/05 ID# M731321Toll-Free Customer Service Number for U.S: 1-800-558-5234,For Canada: 1-800-284-8339,For Europe: 00 800 555 85234 (Sweden: 009 55
10ID# M731321 11/05While maintaining alignment, bounce pole top (4) and middle section (5) together as shown untilthey no longer move toward identif
1111/05 ID# M731321While maintaining alignment, bounce assembly and bottom pole section (6) together as shownuntil they no longer move toward identi
12ID# M731321 11/05Install wheel axle (2) through wheel carriage (19) and install wheels (3) onto wheel axle (2) withspacers (17) as shown. Insert
1311/05 ID# M731321111212106610110136.Secure flat end of tank struts (10) to pole using bolt (11), washers (12), and nut (13), asshown. Rotate the
14ID# M731321 11/058.Install pole mount bracket (27) and reinforcement bracket (34) with carriage bolts (28)in lower pole mounting holes as shown. T
1511/05 ID# M731321This is what your system will look likewhen you’ve finished this section.ITEMS REQUIRED FOR THIS SECTIONSECTION B: ATTACH THE BAC
16ID# M731321 11/05442.41Identify elevator tubes (41 and 44).Toward PoleUpper Elevator tubeLower Elevator tubeAssemble backboard brackets (29) using
1711/05 ID# M731321Attach lower elevator tubes (41) to backboard brackets (29) usingspacers (42) bolt (22) and nut (21) as shown. Insert “T” bolt (3
18ID# M731321 11/0522422144444.Attach upper elevator tubes (44) to backboard support brackets (29) using spacers (42), bolt (22),and nut (21) as sho
1911/05 ID# M73132121444422224121144415.Support pole on sawhorse. Attach upper and lower elevator tubes (41 and 44) to upper polesection (4) using b
2ID# M731321 11/05BEFORE YOU START!To ensure optimal playability of backboardsystem, a close tolerance fit between theelevator components and hardwa
20ID# M731321 11/056.Insert locking pin (46) into bracket on adjustment tube (49). Insert cross pin (45) through hole inbracket and locking pin (46)
2111/05 ID# M7313217.Insert spring (50) into back of locking pin (46) as shown. Spring (50) should rest between twosmall ribs at the back of the pl
22ID# M731321 11/0522515149218.9.41Finish handle assembly by attaching right handle(48) using screws (18) as shown.Attach adjustment tube (49) to lo
2311/05 ID# M7313211323275210.Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull trigger to allowlower adjustment rod to mov
24ID# M731321 11/053132362030363840ABCDE36364038Install Slam Jam Rim to Backboard A. Fit rim (20) securely into bracket (32) as shown. Allow T-bolt
2511/05 ID# M73132112.Support system on sawhorse. Extend system to highest position before assembly of spring.Attach counterbalance spring (43) to u
26ID# M731321 11/05NOTE: Slide counterbalancespring against elevator tubes.Install net (26) as shown. 13.B.D.C.A.Lock elevator system into highest
2711/05 ID# M73132115.2424Roll completed assembly to desired position. Fill tank with water (approx. 30 gallons/115Liters) or sand (approx. 300 lbs
28ID# M731321 11/05Apply the height adjustment and moving label (25) to the front of the pole as shown.17.16.Pull trigger (33). Move elevator system
311/05 ID# M731321SAFETY INSTRUCTIONSFAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY ORPROPERTY DAMAGE AND WILL VOID WARRAN
4ID# M731321 11/05IMPORTANT!Remove all contents from boxes.Be sure to check inside pole sections,hardware and additional parts are packed inside.WAR
511/05 ID# M731321FRONT VIEWPOLESUPPORT STRUTBASEGet to know the basic parts of your basketball system...ELEVATOR ADJUSTMENTBACKBOARDRIM
6ID# M731321 11/05PARTS LIST - See Hardware IdentifierItem Qty. Part No. Description1 1 206657 Tank, (Black)2 1 200628 Wheel Axle3 2 226401 Wheel, 4
711/05 ID# M731321HARDWARE IDENTIFIER (BOLTS AND SCREWS)HARDWARE IDENTIFIER (NUTS AND WASHERS)Item #8 (1)Item #11 (1)Item #12 (6)Item #13 (2)Item #1
8ID# M731321 11/05HARDWARE IDENTIFIER (STEEL SPACERS)HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS, CLIPS AND OTHER)Item #42 (4)Item #31 (1)Item #51 (2
911/05 ID# M731321Correctly identify each pole section. Poles have an identification sticker that will be used as areference point in the next step
Commenti su questo manuale