Huffy 21168202 Manuale Utente

110/04 P/N 21168202© COPYRIGHT 2004 by HUFFY SPORTSInground SystemOwners ManualCustomer Service Center• N53 W24700 South Corporate Circle • Sussex, WI

10P/N 21168202 10/0443Fill hole completely with concrete.6.1" (2.54 cm)51" (2.54 cm)7.Tamp down concrete to release air pockets and build dr

10/04 P/N 2116820211After concrete has cured, remove bottom pole section from ground sleeve (4). Place anti-skid tape (36)around the bottom area of bo

12P/N 21168202 10/04159.Stack and bounce bottom (3) and middle (2)pole sections together. Bounce pole sectionstogether until middle section no longer

10/04 P/N 211682021314077FRONT SIDE11.Install pole mount bracket (6) and bracket reinforcement (40) with carriage bolts (7) as shown. Tighten flange n

14P/N 21168202 10/04126121313119101012. 681414171513. Attach spacers (12, 13) to pole mount bracket (6) with bolts (9), washers (10), andnuts (11) as

10/04 P/N 211682021520193837211814.2015.16Insert handle assembly through polemount assembly as shown. Lock pole assembly in place at the10’ (3.05 m) m

16P/N 21168202 10/04SECTION B: ASSEMBLE THE ELEVATOR TUBES TO BACKBOARD30Upper Elevator tube28Identify elevator tubes (28 & 30).9/16”3/4”1/2”(2) W

10/04 P/N 211682021748311192549Assemble backboard supportbrackets (25) using bolts (9 & 48),spacers (31), and nuts (11 & 49) asshown. 2.282422

18P/N 21168202 10/043.2553535352534.Attach upper elevator tubes (30) to backboard support brackets (25) using spacers (22), bolt (27), and nut(24) as

10/04 P/N 2116820219SECTION C: ATTACH THE BACKBOARD & ELEVATOR ASSEMBLYTO POLE SYSTEM3/4”#27#46#24#45#23#39#44#43#33TOOLS REQUIRED FOR THIS SECTIO

2P/N 21168202 10/04BEFORE YOU START!To ensure optimal playability of backboard system, aclose tolerance fit between the elevator componentsand hardwar

20P/N 21168202 10/041.1243030232323232428282.Support pole on sawhorse. Attach backboard assembly to top pole section (1). Install handle assembly to l

10/04 P/N 21168202213.4346454142Install Slam Jam Rim to Backboard 3244424546ABCDEA • Fit rim (32) securely into bracket (41) as shown (Allow "T&q

22P/N 21168202 10/044.24273030Insert bolt (27) through left side of short elevator tube (30),then stretch spring or springs (29) onto bolt (27). Inser

10/04 P/N 2116820223Fill pole with concrete approximately 1” (2.54 cm)below bottom elevator hole as shown. IMPORTANT!: WAIT A MINIMUM OF 24 HOURS BEFO

24P/N 21168202 10/049.Install clips.Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so thatsecond “arm” slides over the top

10/04 P/N 2116820225Twist net until it snaps into position. Net must be centered through clip. NET INSTALLATION10. 323334Insert net into bottomof clip

26P/N 21168202 10/04SECTION D: UPRIGHT, SECURE AND USE POLE SYSTEMWedgeHammerNoneThis is what your system will look like whenyou’ve finished this sec

10/04 P/N 211682022752.1.After concrete has cured, remove tape, install pole cap (26), fit pole assembly into sleeve (4).Use wedge to gently tap cap o

28P/N 21168202 10/044.16B.A.C.3.A.While holding handle, remove pin (16).B.Move elevator up or down to desired height.C.Replace pin (16) full length to

10/04 P/N 211682023SAFETY INSTRUCTIONSMost injuries are caused by misuse and/or not following instructions.Use caution when using this system.• If usi

4P/N 21168202 10/04For more information on assembly, placement, properuse, and maintenance, visit The American BasketballCouncil website at http://www

10/04 P/N 211682025#8 (9)*#10 (4)HARDWARE IDENTIFIER (BOLTS & SCREWS)HARDWARE IDENTIFIER (NUTS & WASHERS)HARDWARE IDENTIFIER (METAL SPACERS)#1

6P/N 21168202 10/04#44 (1)#41 (1) #43 (1)HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS)HARDWARE IDENTIFIER (OTHER)#23 (4)#22 (4)#12 (2)#39 (2)#33 (

10/04 P/N 211682027TOOLS REQUIRED FOR THIS SECTIONHARDWARE USED IN THIS SECTION (not actual size)SECTION A: ASSEMBLE THE POLE Phillips-Head Screwdrive

8P/N 21168202 10/041TOPMIDDLEBOTTOM231.Mark pole sections with tape (not supplied) at indicated distances from ends as shown.Tape (Not Supplied)18&quo

10/04 P/N 2116820294.1" (2.54 cm)SIDE VIEWFill hole approximately 1/3full with mixed concrete.FIG. AFLANGEInsert ground sleeve assembly and cente